How does granulation affect the composition of plant extract ingredients?
From the perspective of professional formulation chemistry and plant component stability, the effect of granulation on plant extract components is two-directional. It may realize protection and enhancement of active ingredients through process optimization. It may also cause degradation, loss or spectral shift of characteristic components due to out-of-control process parameters.
Positive Protection and Enhancement Effects
- Matrix embedding locks in activity: cooling spray granulation uses oil and wax carriers to fully coat the extract, isolating oxygen and moisture. The oxidative degradation rate of easily oxidized components such as goji polysaccharides and flavonoids is reduced by more than 30%.
- Low-temperature process avoids heat damage: dry granulation has no high-temperature drying step throughout the process. The retention rate of heat-sensitive volatile oils and alkaloids is 20% higher than that of traditional wet granulation. Thermal decomposition of active ingredients is avoided.
- Taste masking while isolating gastric acid: the acid-resistant matrix on the outer layer of the granules allows the extract to avoid the strongly acidic environment of the stomach. The extract is released at a targeted site in the intestinal tract. Acid-unstable components such as anthocyanins and saponins are prevented from being destroyed by gastric acid.
- Stable full-component spectrum: the physical state of the extract after granulation is highly uniform. After 24 months of storage, the relative retention time deviation of characteristic peaks in the HPLC fingerprint can be controlled within 2%. This is far lower than the 10% of native fine powder.
Negative Component Changes Caused by Process Out of Control
- Solvent-induced degradation in wet granulation: if the binder is selected improperly, some plant polyphenols and tannins will undergo complexation reactions with starch slurry or HPMC. The proportion of free active ingredients decreases.
- Component loss caused by high-temperature drying: when the drying temperature of fluid-bed wet granulation exceeds 80 °C, heat-sensitive components such as imperatorin and volatile oils in Angelica dahurica show obvious volatilization loss.
- Component denaturation caused by high-pressure extrusion: when the roller pressure of dry granulation exceeds 100 kN, some plant proteins and polysaccharide macromolecules undergo local conformational changes. Biological activity shows an irreversible decrease.
- Component interference introduced by binders: if the purity of the added excipients does not meet the standard, impurities may be introduced and undergo side reactions with flavonoids and anthraquinones in the extract. Non-characteristic impurity peaks of the raw material appear in the fingerprint.
Differences in Granulation Sensitivity Among Different Types of Plant Components
- Polysaccharides (goji polysaccharide, Dendrobium polysaccharide): sensitive to high temperature and high humidity. Dry granulation causes almost no component loss. Conventional wet granulation with drying at 80 °C has a retention rate of about 85%.
- Alkaloids (Coptis berberine, tetrahydropalmatine): sensitive to pH and high temperature. In wet granulation, the pH of the binder must be controlled within the range of 5–7. Otherwise hydrolysis easily occurs.
- Flavonoids (Ginkgo flavonoids, baicalin): easily oxidized. With inert gas protection introduced during granulation, the oxidative degradation rate can be controlled within 5%.
- Volatile oils (peppermint oil, Angelica dahurica volatile oil): extremely sensitive to heat. Only cooling spray melt granulation is recommended. The loss rate of the traditional hot-air process can be as high as 60%.
Common Industry Control Methods for Component Verification
- Before and after granulation, TLC thin-layer chromatography is used to compare characteristic spots. It quickly confirms that no signature component is lost.
- For high-value pharmaceutical-grade extracts, full-spectrum verification by HPLC fingerprint is used. The relative area deviation of more than 27 characteristic peaks is ensured to be no more than 5%.
- For heat-sensitive components, the activity retention rate before and after granulation is additionally tested. It serves as a core indicator for process release.
- Accelerated stability testing verifies that the content decline of the target component is no more than 10% within a 6-month accelerated storage period.
If you also have a plant extract component that needs granulation, you are welcome to leave a message for consultation. We will arrange a professional sales representative to contact you.





