How to Solve Tower Sticking in Spray Dried Plant Extracts
As a professional plant extract production technical team in China, NutraLighting has rich experience in product manufacturing. In this article, we will share professional solutions to the tower sticking problem of spray dried plant extracts. We first need to accurately distinguish three typical causes: sticking by semi wet materials, sticking by heat melting materials, and static adhesion of dry powder. Then we carry out systematic measures from four aspects: material pretreatment, process parameters, equipment structure and compliant operation. Finally, the sticking rate can be controlled within the qualified range of the industry.
Material Pretreatment and Formula Optimization (Reduce Sticking from the Source)
Accurate compounding of drying aids: Use maltodextrin with a DE value of 10-20 as the main material, together with β-cyclodextrin and gum arabic. The adding amount accounts for 5%-30% of total solids. It can raise the glass transition temperature of the system by more than 15℃ and reduce the heat melting stickiness of powder fundamentally.
Addition of compliant anti sticking agents: On the premise of meeting relevant requirements, add 0.5%-2.0% fumed silica or tricalcium phosphate. They form a physical isolation layer between particles and greatly lower surface stickiness and static adsorption of powder.
Homogenization of feed liquid to reduce viscosity: Control the solid content of feed liquid at 12%-26%. Preheat it to 50-65℃ and then treat it with a colloid mill and high pressure homogenization under 20-30 MPa. It intercepts pulp fiber and pectin lumps above 100-120 mesh and prevents large atomized droplets from touching the tower wall in advance.
Enzymatic pretreatment for viscosity reduction: For extracts with high sugar and high pectin content, add 1% cellulase and carry out hydrolysis at 50℃ for 30-60 minutes. It can greatly cut the viscosity of feed liquid without adding a large amount of drying aids and meet the purity requirement of pure powder.
Systematic Calibration of Process Parameters (Core Sticking Control Method)
Precise control of temperature gradient: Follow the principle of “setting outlet air temperature first, then adjusting inlet air temperature”. Set the inlet air temperature 5-10℃ below the glass transition temperature of materials. Keep the temperature difference between inlet air and outlet air at 35-45℃. Never let the inlet air temperature exceed 180℃ to avoid sugar coking, melting and wall sticking.
Matching and optimization of atomization system: Set the rotating speed of the centrifugal atomizer disc at 12000-22000 r/min, and the pressure of two fluid atomization at 0.2-0.7 MPa. Keep the median droplet size D50 stable at 20-80 μm to make sure droplets are fully dried during their flight.
Dynamic balance of air flow field: Keep the empty tower gas velocity at around 0.18 m/s and maintain a slight negative pressure of -50 ~ -100 Pa inside the tower. It removes dead zones of hot air vortex and stops undried fine powder from being drawn to the tower wall by air flow.
Linked adjustment of feeding rate: Use a frequency conversion feed pump for precise control. Match the feeding rate in real time with inlet air temperature and air volume. Prevent excessive instantaneous feeding beyond the drying load of equipment, which causes semi wet material sticking.
Targeted Modification of Equipment Structure (Hardware Guarantee against Sticking)
Upgrade of hot air distributor: Adopt a hot air distributor with an abrupt inlet volute structure together with primary air cooling technology. It ensures uniform hot air flow inside the tower, eliminates the phenomenon of “droplets flying back to the top”, and reduces top sticking through flow field design.
Optimization of anti sticking structure for tower body: Install a jacket cooling device on the tower wall to keep the wall temperature below the softening point of materials. Increase the cone angle of the cone section and fit air knockers, which strike every 10 minutes. Pulse compressed air knocks down attached powder.
Polishing of inner wall: Fine polish all inner walls in contact with materials to Ra ≤ 0.8 μm. Remove sand holes and dead zones for powder accumulation, lower the chance of static adsorption of powder, and satisfy the sanitary standards for plant extract production.
Supporting air sweeping system: Arrange directional air wall sweeping devices around the tower wall. Clean compressed air of 0.2 MPa blows continuously to sweep away loosely attached wet powder on the cone section and stop thick material layers from forming after long term accumulation.
Standardized Operation and Compliance Control (Basis for Long term Stable Operation)
Specification for preheating before startup: Run the whole tower without load for preheating 30 minutes in advance. Start feeding only after the tower wall temperature stabilizes at the set value. It avoids wet powder sticking caused by water vapor condensation on cold walls.
Traceability of process parameters: Build process files of “solid content – temperature – feeding rate – atomization pressure”. Record key parameters for each batch to ensure repeatable production.
Regular maintenance and calibration: Clean residual materials inside the tower right after each batch. Calibrate the atomizer speed every week and check nozzle wear every quarter. Prevent uneven atomization and offset spraying hitting the wall caused by equipment aging.
Control of environmental humidity: Install dehumidifiers in the production workshop. Keep the relative humidity of the environment at 45%-65%. Stop accumulated water vapor inside the tower under high humidity from worsening powder moisture absorption and sticking.

Spray Dryer Tower Internal View
The commonly accepted industry standard at present is as follows: when the air sweeping system works normally, if the original color of the inner wall can still be seen after 5 consecutive days of continuous production with no obvious material accumulation, the natural powder collection rate of the spray drying process reaches ≥90%, and the total yield reaches ≥95%, the tower sticking problem is judged to be effectively solved. There is no unified mandatory standard for tower sticking prevention covering all types of plant extracts. In practical use, we need to find the optimal parameter combination step by step through lab tests based on DSC test results of the glass transition temperature of specific materials.
Certainly, differences exist among different products and equipment. Every product needs strict research, lab tests, pilot tests and formal production. If you meet production problems of some products, leave a message or contact the sales team of NutraLighting.





